Neopro Tahoe-Veo Bedienungsanleitung

Integrator’s Guide Tahoe™ Video Distribution System

10 Before connecting CAT5 cables, make sure the wire pairs are terminated as shown in Figure 1 and Table 1 below. The common standards known as 568A

DOC42-00035-A-Tahoe_Integrators_Guide.doc 11 grounded. A display with a three wire AC plug meets this requirem

12 IR Remote The factory IR remote (optional) is shown below. Although the button locations are not exactly the same as the front panel, they serve

DOC42-00035-A-Tahoe_Integrators_Guide.doc 13 IR Inputs Located on the front panel is a small box labeled ―IR I

14 Standby Mode When in Standby Mode, all outputs are virtually disconnected. In this state, the switch can still execute commands from the serial po

DOC42-00035-A-Tahoe_Integrators_Guide.doc 15 Matrix Routing Status  OUTPUT 1   IN: 07  Starting from

16 Setup Item Description SET: Panel LED Controls the front panel button LEDs. Default is ON. SET: Disp Lamp Sets the display brightness to 1 of 4 le

DOC42-00035-A-Tahoe_Integrators_Guide.doc 17 Setup Item Description SET: FaultMode If a power supply or fan fa

18 + X X To store to a memory location from the IR remote, press the ‗Stop‘ button and the two digit memory slot number. The system will then store

DOC42-00035-A-Tahoe_Integrators_Guide.doc 19 may create an opportunity to inspect the fan and remove dust or p

2

20 Adding Output Cards Overview Adding more outputs to the system can be done by adding one or more Cat5 16 output cards. The following instructions

DOC42-00035-A-Tahoe_Integrators_Guide.doc 21 Figure 2 - Save these two screws for attaching add-in card. Inst

22 Figure 3 - Always wear ESD while handling the boards Returning to Service 1) Reinstall the system into the rack. 2) Reinstall all signal cables

DOC42-00035-A-Tahoe_Integrators_Guide.doc 23 Adding and Hot Swapping Power Supplies Overview Removing and repl

24 Serial Protocol Serial Port Settings The serial port operates at 115.2k baud, no parity, 8 data, 1 stop. No hardware flow control is used. Convent

DOC42-00035-A-Tahoe_Integrators_Guide.doc 25 invalid characters/values/command between the braces, they will b

26 [TV,ii,oo] ii is the one or two digit source input number. If this number is 0, then the selected output will be disabled. oo is the one or two di

DOC42-00035-A-Tahoe_Integrators_Guide.doc 27 x n Setup function S L Front Panel Sensitivity LOW S M Front Pane

28 The Memory Command structure begins with M: [M,x,n] x n (memory location) Memory Function S 1-16 Store current state to memory location n R 1-16 R

DOC42-00035-A-Tahoe_Integrators_Guide.doc 29 [?S,C] The fault message contains a fault code number as shown be

DOC42-00035-A-Tahoe_Integrators_Guide.doc 3 Table of Contents Table of Contents ...

30 through a normal serial port should be able to control the matrix through a USB port. This driver set is for all versions of MS Windows. Linux and

DOC42-00035-A-Tahoe_Integrators_Guide.doc 31 Step 2 – Found New Hardware Wizard The first window will attempt

32 Step 3 – Driver location The next window attempts to find the driver disc. Insert the driver CD disc in the CD-ROM drive if you haven‘t already.

DOC42-00035-A-Tahoe_Integrators_Guide.doc 33 Step 4 – Continue Anyway Windows will prompt on logo testing. Cl

34 Step 5 – Completion of first half Click ―Finish‖.

DOC42-00035-A-Tahoe_Integrators_Guide.doc 35 Step 6 – Installing virtual COM port driver Windows will again s

36 Step 7 – Finding the driver Leave the button labeled ―Install the software automatically (recommended)‖ selected, and click Next.

DOC42-00035-A-Tahoe_Integrators_Guide.doc 37 Step 8 – Continue Anyway Windows will prompt on logo testing. Cl

38 USB COM Port Settings Whether using a Windows terminal program such as Hyperterminal, a control application, or a dedicated control system, the ba

DOC42-00035-A-Tahoe_Integrators_Guide.doc 39 Uninstalling the USB drivers There is typically no harm in leavin

4 Adding Output Cards ... 20 Overview ...

40 Care and Maintenance The NeoPro matrix switch does not require any regular maintenance besides keeping it clean. Never use harsh cleaners or solve

DOC42-00035-A-Tahoe_Integrators_Guide.doc 41 Specifications Performance Component Video Input coupling AC

42 Notes:

DOC42-00035-A-Tahoe_Integrators_Guide.doc 43 2 Year Warranty NeoPro warrants this product against defects in

44 © 2011 NeoPro www.neoprointegrator.com

DOC42-00035-A-Tahoe_Integrators_Guide.doc 5 Introduction Congratulations on your purchase of the NeoPro Tahoe

6 System Installation Rack Mounting Your Tahoe system ships with the rack mounting ears attached to the chassis. Installing the unit into the rack

DOC42-00035-A-Tahoe_Integrators_Guide.doc 7 Inputs and Outputs All signal and control connectors are on the r

8 Connector Labels Signal type(s) Y, Pb, Pr High definition component video inputs 1 - 80 High definition component video outputs over Cat5 IR Input

DOC42-00035-A-Tahoe_Integrators_Guide.doc 9 Cat5 Cables and Receivers HD Video Quality & Cable Length The